Dome CameraOwner’s ManualMODEL: LPT-OS551HQLPT-OS553HQBefore installing and using the camera, please read this owner'smanual carefully and retain

10Setting the SwitchThe DIP switch of the camera is two 4-bit switchesand employs RS-485 communication mode as basicuse. Switch settings are read into

114. Turn on the camera. Setup is completed.Camera ID SettingThis camera has the camera ID set to “1” at the timeof the shipment. If you use 2 cameras

12ID SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW853 ON OFF ON OFF ON ON OFF OFF54 OFF ON ON OFF ON ON OFF OFF55 ON ON ON OFF ON ON OFF OFF56 OFF OFF OFF ON ON ON O

13ID SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8159 ON ON ON ON ON OFF OFF ON160 OFF OFF OFF OFF OFF ON OFF ON161 ON OFF OFF OFF OFF ON OFF ON162 OFF ON OFF OFF O

14Precautions• The connections should be made by qualifiedservice personnel or system installers in accor-dance with all local codes.• DC 12V can be u

15ALARM IN ConnectionsAn 8-pin harness are supplied with the camera asstandard accessories. Connect external sensors tothis connector. Input specifica

16Alarm Input functionListed below are the camera actions of alarm input function by different function status in each mode Manual modeChange the obse

17System ConnectionTo Alarm sensor1 ALARM IN 1 BrownBlueYellowGreenRedBlackOrangeWhite2 ALARM IN 23 GND4 TRX D-5 TRX D+6 GND7 ALARM IN 38 ALARM IN 4RS

18Setup Menu OverviewSetup menus are shown in the table below. You can adapt the camera to your requirements by setting up therespective items in thes

19Setting Camera MenuThe buttons on the connected controller are used forsetup.Open Menu Display1. Select the number of the camera you want to setup a

2This lightning flash with arrowhead symbolwithin an equilateral triangle is intended toalert the user to the presence of uninsulat-ed dangerous volta

20Camera Identification SettingOnly displays the camera’s ID. Use the internal 8 bit-DIP switch if you want to set ID.• Camera ID 0 can control all of

21Zoom Start settingSelects a zoom start position.Select [ZOOM START] option on the [FOCUS] menu,then select a zoom’s start position. (x1 - x26)Zoom E

22White Balance Control SettingsYou can set the white balance options using the[AWB] menu.General Operation1. Move the cursor to [AWB SET] on the [MEN

23Exposure SettingsYou can set the exposure options using the [AE]menu.General Operation1. Move the cursor to [AE] on the [MENU] screen 2. Press the r

24Automatic Gain Control (AGC) settingIf the images are too dark, change the maximum[AGC] value to make the images lighter. This optionis available on

25Electronic Sensitive settingThe electronic sensitivity enhancement functionvaries the shutter speed to increase the sensitivity inlow light conditio

26Auto Exposure Level SettingsYou can set the auto exposure options using the [AE LEVEL] menu.General Operation1. Move the cursor to [AE LEVEL] on the

27Special SettingsYou can set the special options using the [SPECIAL]menu.General Operation1. Move the cursor to [SPECIAL SET] on the[MENU] screen 2.

28Color Setting You can switch the displayed picture to grayscale orcolor.Select [COLOR] option on the [SPECIAL] menu, thenselect an option (ON or OFF

29Motion Detection SettingThe motion detection detects the moving objects inthe scene by monitoring changes in brightness level.You can select the lev

31. Read these instructions. - All these safety and operatinginstructions should be read before the product is operat-ed.2. Keep these instructions. -

30Privacy Masking SettingsUsing the LCC-K1000 or controller with Multix protocol for Privacy Zone Setting.This function is aiming at the protection of

31SpecificationsSignal System NTSC (High Resolution) PAL (High Resolution)Pick-Up Device 1/4” EX-view HAD CCDTotal Pixels No. 410K 470KS/N Ratio More

P/NO : MFL40426602LPT-OS553HQ_ENG_6602 7/19/07 2:08 PM Page 32

4ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-7IMPORTANT SAFETY INSTRUCTIONS . . . . . . . .3Contents . . . . . .

5xxPattern FunctionA routine of manual operations can be stored for 5minutes at the maximum and reproduced repeti-tively. The Panning, Tilting and Zoo

6Safety PrecautionsxxDo not attempt to disassemble the cameraTo prevent electric shock,do not remove screws orcovers. There are no user serviceable pa

71 Camera mounting bracket2 Dome camera body3 Dome cover4 Power cable (DC 12V)5 Video output cable with BNC connectorConnects with the video connector

8InstallationPrecautions• The following steps of installation and connectionwork should be done by qualified service person-nel or system installers a

9Pendant mount (Optional) Wall mount (Optional) How to install“A” Pipe threads should be clean andrust free. Use a sealer (such asTeflon™ tape or sil