LG LNP3020T Manuale Utente Scaricare il pdf (Pagina 2)

Connecting Display device

The video signal connection between the

camera and the monitor.

ALARM input connection

Connect sensor and alarm devices to

corresponding terminals accordingly.

Alarm device

Terminal BlockTerminal Plug

Description Color

A ALARM IN 1 Brown

B ALARM IN 2 Red

C ALARM IN COM Black

D ALARM IN 3 Orange

E ALARM IN 4 Green

ALARM output connections

Terminal Block

Alarm device

Terminal Plug

Description Color

A ALARM OUT 1A Blue

B ALARM OUT 1B Violet

C ALARM OUT 2A Gray

D ALARM OUT 2B White

CAUTION:

Output specifications are lowactive, open-

collector and a drive capacity of DC 30 V 1

A/ AC 125 V 0.3 A. Connecting the alarm out

incorrectly may cause damaging the camera.

Connecting IP Reset

Connect the 2 (IP Module Reset Terminal)

and 3 (GND) to reset the IP address as

shown below.

IP Module Reset

Terminal

GND

Terminal BlockTerminal Plug

Description Color

A IP Module Reset Terminal Pink

B GND Yellow

Connecting Network

Connect the IP camera to your network

using a standard Terminal block as shown

below.

Router

Connecting power source

Connect a AC 24 V or PoE+ power source to

the power input terminal as shown below.

(Recommended power adaptor is AC 24 V/3

A or above.)

NOTES:

• In case of connecting both AC 24 V and

PoE+, PoE+ has a priority.

• Do not connect the power source AC 24 V

and PoE at once.

AC 24 V

PoE+

Connecting Microphone and

Speaker Device

Optionally connect an active speaker and/or

external microphone with a built-in amplifier.

NOTE:

Keep the microphone away from the speaker

to avoid howling.

You can record your surveillance environment with the SD card even if the network is disconnected

condition.

To insert the SD card

1. Remove the dome cover.

2. Insert the SD card carefully as shown in the following illustrations. Make sure the SD

card

terminal position before insert the SD card. Push the back end of the SD card to fix it at the last

step.

NOTES:

• Do not use the power too much when you insert the SD card. The SD card may be

damaged.

• If you insert the SD card in the wrong position, the SD card may be damaged or it may cause

the malfunction of the SD Card Slot.

• Keep the terminal part of the SD card in clean. Be careful the terminal part of the SD card

not to dusty.

• As the SD card is consumable, the SD card end its days and may be not able to save data if

you use it more than over certain times. In this case, replace SD card to buy

a new one.

Remove the SD card

1. Press the back end of the SD card to release the lock condition.

2. Take the SD card out carefully from the camera. It may cause a malfunction of the SD

card

or the SD card slot if you use the power too much at lock status.

CAUTION:

• If you install the SD card on the camera and remove with the SD card condition indicator

lights on, you must unmount the SD card by using the [SD Card > Configuration > Disk

Management > Unmount] menu. The SD card data is compromised or the camera may

not operate normally, if you remove the card without use [Unmount] function.

• Do not insert Micro SD card to SD card adapter. It is recommended to use a standard SD

card.

• Insert the SD card before install the camera.

• LG Electronics is not responsible for deleted data caused by user mishandling when you

insert or remove the SD card.

Precautions

• Remove the dome cover carefully to

prevent falling.

• Before using the camera, remove the

protection tape. Loosen the screws using

the wrench and remove the dome cover

as shown below.

• Align the s mark of the dome cover

and LG logo of the camera assembly for

proper camera orientation.

• Remove the protection tape after

installation is completed.

Wall mount (optional)

Install the camera by the following order.

1. Install the wall mount assembly as

shown below.

2. Drill a hole on the wall where you want

to install the pipe. Pass the connection

cable through the wall mount assembly

so that they hang down.

3. Connect the safety cable to the camera

in order to prevent a camera from falling.

4. Connect the cables to the camera jack.

5. Assemble the camera to the mounting

adaptor by turning it clockwise. Tighten

the M3 SAMS Screws and then align the

cover adaptor and main body.

Pandent mount (optional)

Install the camera by the following order.

1. Install the pandent mount assembly as

shown below.

2. Drill a hole on the wall where you want

to install the pipe. Pass the connection

cable through the pendant mount

assembly so that they hang down.

3. Connect the safety cable to the camera.

4. Connect the cables to the camera jack.

5. Assemble the camera to the mounting

adaptor by turning it clockwise. Tighten

the M3 SAMS Screws and then align the

cover adaptor and main body.

Parapet mount (optional)

1. Install the parapet mount assembly as

shonw below.

2. Drill a hole on the wall where you

want to install the parapet. Pass the

connection cable through the parapet

mount assembly so that they hang

down.

3. Connect the safety cable to the camera.

4. Connect the cables to the camera jack.

5. Assemble the camera to the mounting

adaptor by turning it clockwise. Tighten

the M3 SAMS Screws and then align the

cover adaptor and main body.

Connection Using the SD Card

Installation

1 2

Commenti su questo manuale

Nessun commento

LG LNP3020T Manuale Utente Pagina 2

Commenti su questo manuale

Prodotti e manuali riguardandi Telecamere di sicurezza LG LNP3020T